It is currently Wed Jul 30, 2014 8:08 am

Post a new topicPost a reply Page 1 of 1   [ 2 posts ]
Author Message
 Post subject: Arduino Meta-Project: remote control panel
PostPosted: Thu Nov 18, 2010 9:33 pm 

Joined: Sun Oct 31, 2010 7:52 am
Posts: 11
After getting the automatic chicken door working (see my previous Forum post), I decided to try something I've want to do for a long time: to be able to use my favorite software development tool to create "control panels" to remotely control an Arduino. "Remote" is relative: for now, it means via a serial port and N inches/feet of wire. Eventually I hope to work my way up to doing it with Zigbee or Bluetooth...

So I have a software tool (called LiveCode) that lets me build GUI interfaces and talk to a serial port with very, very few lines of easy-to-understand code. I plan to offer an intro class in LiveCode very soon. For now, if you'd like to see what it's about, check:

On my laptop, I created a small control panel to turn an LED on/off or make it blink at a user-selectable rate:


I then defined a set of command-strings to send over the serial port:

"0"= LED off
"1"= LED on
"Bnnnn" = blink the LED every nnnn milliseconds

And finally I wrote and debugged (and debugged...) the Arduino sketch to read the command-strings, parse them, and execute them:

// Remote control of an LED via the serial port
//    Larry Walker    11/14/10

//  turn an LED on/off according to input from the serial port
//    received char = 0 means turn LED off
//    received char = 1 means turn LED on

byte incomingByte = 0;   // for incoming serial data

int delayVal = 0;       // duration of blink, in millis (0 means no blinking in effect)
int delayCnt = 0;       // counter to step through the delayVal
int blinkState = LOW;   // state variable for blinking LED

const int LED1 = 13;    // define pin for LED1

void setup() {
  Serial.begin(9600);   // opens serial port, sets data rate to 9600 bps

  // initialize the digital pin as an output.
  // Pin 13 has an LED connected on most Arduino boards:
  pinMode(LED1, OUTPUT);     

void loop() {

  // see if there's a command waiting
  if (Serial.available() > 0) {
    // read the incoming byte:
    incomingByte =;

    // say what you got:
    Serial.print("I received: ");
    Serial.print(incomingByte, BYTE);

    // decide what to do to the LED
    switch (incomingByte) {

    case '0':
      // turn the LED off when command equals ascii 0
      digitalWrite(LED1, LOW);
      Serial.println("     turning LED off...");
      delayVal = 0;     // suppress any pending blinking

    case '1':
      // turn the LED on when command equals ascii 1
      digitalWrite(LED1, HIGH);
      Serial.println("     turning LED on...");
      delayVal = 0;     // suppress any pending blinking

    case 'B':
      // start blinking the LED when command equals ascii B
      // suck up the delay value
      delayVal = 0;
      while (Serial.available() > 0) {
        // read the next incoming byte:
        incomingByte =;
        if ((incomingByte >= '0') && (incomingByte <= '9')) {
          delayVal = (10*delayVal) + (int(incomingByte) - '0');
      delayCnt = 0;
      Serial.print("     blinking LED every ");
      Serial.print(delayVal, DEC);
      Serial.println(" ms...");
      delayCnt = delayVal-1;     // suppress any pending blinking

      // if nothing else matches, do the default
      Serial.print("     Invalid command!");
    }  // end of switch (incomingByte)
  }  // end of if (Serial.available)
    // no incoming command, see if we need to do blinking thing
    if (delayVal != 0) {
      // we have a delayVal, so we're blinking
      // time to toggle the LED?
      if (delayCnt == delayVal) {
        blinkState = !blinkState;
        digitalWrite(LED1, blinkState);
        delayCnt = 0;      // restart the delay period
      }  // end of if (delay expired)
    }  //end of if (delay in effect)
  }  // end of else see about blinking
}  //end of loop

Short video of the pair of apps working together:

I know I need to do some serious refactoring before it's a general-purpose tool, like learning more about Arduino C's string handling libraries so I can parse a more complex command syntax...

So what's it good for?

I want to be able to do this for two general cases:

1) to make an "operator's console" to control a complex Arduino project (permanently connected)

2) to make a "maintenance console" to tweak/calibrate/configure even a simple Arduino project (occasionally connected)

One last detail: if you've ever tried to program GUIs (graphic user interfaces) in conventional languages, you know what a pain it can be and you won't believe how painless LiveCode is. I wrote zero lines of code to build the GUI itself: I just dragged & dropped 5 Button objects, 2 Label objects and a Slider object from a tool palette, positioning them where I wanted them with no long gnarly create_object() calls or set_object_position() calls.

The code to send the messages to the Arduino was almost laughably short and simple. The messiest were the code for the Open Port and the Blink LED objects:

Open Port:
global usbSerial

on mouseUp
   open driver usbSerial for binary update
   enable button "Close Port"
   enable button "LED On"
   enable button "LED Off"
   enable button "Blink LED"
   disable me
end mouseUp

Blink LED:
global usbSerial

on mouseUp
   enable field "delayLabel"
   enable scrollbar "Delay"
   enable button "LED On"
   enable button "LED Off"
   put the thumbPosition of scrollbar "Delay" into delayVal
   write "B" & delayVal & return to driver usbSerial
end mouseUp

Notice that over half the lines of code are mostly showing off: they just control which buttons are dimmed when they aren't appropriate (i.e. it doesn't make sense to let the user click LED On until the port has been opened). Without that feature, the actual working code is 2 executable lines per object...

Whew! That was the most software fun I've had in years!

I'll be demo'ing this app and the chicken-door prototype at the December Sector67 meeting, if you have any questions...

Larry Walker

 Post subject: Re: Arduino Meta-Project: remote control panel
PostPosted: Fri Nov 19, 2010 12:25 pm 

Joined: Thu Nov 18, 2010 3:59 pm
Posts: 25
If you want to go wireless, I recommend the RN41 for bluetooth. I use them at work and have a motor drive controlled by the bluetooth on my phone, or on my computer. I usually use VB for my serial com gui controlling needs. I hope to post a quick hyperterminal android app for bluetooth based on the broken google bluechat code.

Display posts from previous:  Sort by  
Post a new topicPost a reply Page 1 of 1   [ 2 posts ]

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

Powered by phpBB